Permanente Hoedenplank fix (meerdere oplossingen !!)

Plaats hier je handleiding of link van een uitgevoerde mod of reparatie! Of stel hier je vraag hoe je een mod o.i.d. moet uitvoeren.

Moderators: Passiepooh, pumamartin, Puma Moderators

Plaats reactie
Zatarra

Permanente Hoedenplank fix (meerdere oplossingen !!)

Bericht door Zatarra » di 24 mei 2011, 6:15 pm

Hierbij mijn beschrijving hoe ik de hoedenplank heb gefixeerd:

Na verschillende pogingen met plakband e.d. bleef dat ding het voor me kaar krijgen weer te vallen.
Wie weet heeft iemand anders dit ook al gedaan maar ben hem nog niet tegen gekomen op het internet.

Doe de hoedenplank in de houder en houd hem omhoog.
Kijk tot hoever die komt en markeer aan beiden kanten een stipje.
Maak op dit stipje een klein gaatje door de 2 lagen heen.
Neem een stukje sterk ijzerdraad of een pin(spijker o.i.d.) of iets dat je hebt liggen en vorm hier een oogje aan.
Steek het pinnetje door de gaatjes heen.

Mooi subtiel opgelost en de hoedenplank is ook nog makkelijk te verwijderen.

gabbagirl

Re: Permanente Hoedenplank fix (gratis)

Bericht door gabbagirl » wo 25 mei 2011, 7:38 am

Ik heb gewoon tape om de uiteinden gewikkeld en nu ligt die steviger in de houder en is er sindsdien nooit meer uitgevallen :wink:

Jeroen.

Re: Permanente Hoedenplank fix (gratis)

Bericht door Jeroen. » za 04 jun 2011, 2:42 pm

Met onderstaande How-to van een Engels forum heb ik de hoedenplank gefixt. :party:
ProjectPuma schreef:Parcel Shelf Fixes

Guide Overview:

This guide will hopefully help you stop the parcel shelf from constantly falling into the boot. It's normally a combination of the hinge / hinge location wearing and the strings not staying on the hatch pins. Sometimes the hinge comes away from the parcel shelf too.

Hinge pin modification

Difficulty: 1/5

Time: 30 mins - 1 hour

Required Tools:
  • Hot air gun / Hairdryer
  • Scissors
Required Parts:
  • Heat shrink sleeving (*see bottom of article)
  • Grommets x 2 (*see bottom of article)
Rather than constantly wrapping electrical tape around the hinge pins, I’ve found that applying heat shrink sleeving is a more permanent fix as it “sets” to a much harder finish than tape ensuring it lasts a lot longer.

1. Remove Parcel Shelf from car. Work on one side at a time.

Afbeelding

2. Apply heat to the 2 plastic hinge sections on the parcel shelf to slightly soften the hinge and allow removal of the metal pin.

Afbeelding

3. With the pin out, cut a length of heat shrink to cover the rubber cylinder.

Afbeelding


4. Using a hot air gun / hairdryer shrink to fit uniformly around the rubber. (thus increasing its diameter)

Afbeelding

5. Insert the metal pin back through the plastic hinge whilst inserting a smaller length of slightly smaller heat shrink to the metal pin between the two hinge parts.
(If you haven't been fast enough with steps 3 and 4, the hinge may have cooled and the pin may be difficult to re-insert. Simply re-heat the hinge and insert the metal hinge.)

Afbeelding

Afbeelding

6. With the hinge in position, gently heat the central heat shrink to ensure the pin never comes out again.
(The plastic hinges will contract round the metal hinge again as it cools down securing it, but this is just to be sure)

Afbeelding

7. Repeat for the other side of the parcel shelf.

8. Wait for the hinge / heat shrink to become cool.

9. Returning to the car – re-fit the hinge back into the hinge location slots. It should be a much firmer push you need now whilst it still pivots.

Before pushing in:

Afbeelding

Pushed in:

Afbeelding

10. Refit the strings to the hatch pins.

Afbeelding

11. Push a grommet over to stop the strings falling off.

Afbeelding

Afbeelding

Mines lasted over a year now with no signs of wear happy

Hinge to parcel shelf fixing modification
If your plastic hinge has come away from the parcel shelf, then the best way to fix it back is to bolt or rivet it back into position. Using any adhesive will only be a temporary fix due to the vibration and contact surfaces involved (carpet / plastic)

Difficulty: 2/5

Time: 30 mins - 1 hour

Required Tools:


* Drill
* Suitable drill size for Rivet / bolt


Required Parts:


* Rivets or Bolt & nuts



1. Drill through the hinge either side of the mounding to ensure a flat surface using the drill and an appropriately sized drill bit.

2. Place on Parcel shelf and mark the position.

3. Carefully drill the parcel shelf (It's thicker than you think!)

4. Place hinge back on shelf and Rivet / screw as required.

Afbeelding

Afbeelding

Job Done

Jeroen.

Re: Permanente Hoedenplank fix (gratis)

Bericht door Jeroen. » zo 05 jun 2011, 1:20 pm

Ik heb die dopjes gewoon met krimpkous gemaakt. Werkt perfect 8)

MiniMan
Puma Senior
Puma Senior
Berichten: 127
Lid geworden op: do 18 feb 2010, 5:51 pm
Facebook Pagina: http://www.facebook.com/#!/MiniRogier
Locatie: Duiven
Contacteer:

Re: Permanente Hoedenplank fix (gratis)

Bericht door MiniMan » ma 06 jun 2011, 10:51 am

Wat heb je nodig:
-2 Zwarte elastieken, deze zitten op tuinslangkoppelingen zie hieronder, zijn los tekoop hoor :wink:
Afbeelding

Afbeelding
1. Doe deze elastieken dubbel om de voet van het koord, zie foto
2. Bevestig het koord zo als je dat altijd doet, en rol daarna het elastiek over de grote opening

Dan de hoedenplank zelf, zo valt die er niet meer uit:
Afbeelding
3. Druk het rubber van de hoedenplank goed strak tegen het kunststof aan, dat die goed klem zit

Afbeelding
4. Doe hetzelfde ook aan de andere kant

Hoop dat het zo duidelijk is, alles is nu nog te demonteren zonder gereedschap en de elastieken zijn los tekoop bij de bouwmarkt/tuinwinkel
Binnenkort trotse eigenaar van een zwarte Reanault Clio 1.6 16v full options

Afbeelding

Iceman
Puma Junior
Puma Junior
Berichten: 65
Lid geworden op: ma 20 feb 2006, 1:13 pm
Locatie: Vlijmen (NBr)

Re: Permanente Hoedenplank fix (gratis)

Bericht door Iceman » zo 19 jun 2011, 7:33 am

Ik heb mijn hoedenplank vastzitten met zo'n metalen klemmetje van TuningHaus.
Kost € 10,00 maar werkt hardstikke prima en de hoedenplank blijft verwijderbaar.
http://www.tuninghaus.de/shop/product_i ... _68_69_360

Idee met krimpkous erom werkt wel maar houd er rekening mee dat je die horizontale kunststof U (geen idee hoe ik dat anders moet omschrijven) waar je die as in duwt extra uit elkaar drukt en deze kan daardoor een keer kapot gaan.
Afbeelding

Plaats reactie